Creating 9 MTD partitions on "ar7100-nor0": Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled io scheduler deadline registered (default) squashfs: version 3.0 (5) Phillip Lougher wl0gpio_proc: module loaded and /proc/wl0gpio/ created gpio_proc: module loaded and /proc/gpio/ created UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) UDP hash table entries: 256 (order: 0, 4096 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) IP route cache hash table entries: 1024 (order: 0, 4096 bytes) found calibration data for slot 1 on 0xBF055000 found calibration data for slot 0 on 0xBF051000 registering PCI controller with io_map_base unset Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) PID hash table entries: 512 (order: -1, 2048 bytes) Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init Built 1 zonelists in Zone order, mobility grouping on. booting platform Atheros AR7161 rev 2 (0xaa) # Giving linux memsize in bytes, 134217728 # Transferring control to Linux (at address 80238490). Image Type: MIPS Linux Kernel Image (lzma compressed) Image Name: DD-WRT v24 Linux Kernel Image Reserving 128k for boot params() at: 83f6bfb0įlash bank #0 found 16 MB flash įlash bank #1 found 16 MB flash Reserving 36 Bytes for Global Data at: 83f8bfb0 Reserving 44 Bytes for Board Info at: 83f8bfd4
#Snmp dd wrt v24 sp2 upgrade
Where is a placeholder for mini, std, voip, etc.įor upgrading from the original Linksys firmware, please use the mini version firstĪfter this first flash you can then upgrade to any distribution of your choice.Top of RAM usable for U-Boot at: 84000000 These versions were just made specifically for TFTPing to those routers.įor initial Flash Your Motorola WR850G (Micro and Mini builds ONLY) You CAN use this to flash via web interface but do so only AFTER you have done so using the mini version. These versions were just made specifically for TFTPing to those routers.
You must use the 'generic' build for TFTPing to these units). (v5/v6 note: Since the WRT54G/GS v5-v6 uses a modified WAP54Gv3 once made 'linux ready', it will not accept these standard WRT54G/GS firmwares. Generic version for flashing via web interface on all supported devices (including Linksys WRT54G/GL/GS) and for flashing Siemens SE505 with boot tftp on 192.168.2.1 (6)Not available on VPN-builds for v24sp1 (see prerequisites for JFFS). (5)Apparently, IPv6-related features DO NOT work by default in DD-WRT v24. (4)Only on DD-WRT v24 (8MB+ flash required) (3)Smaller VPN JFFS builds are available for 4MB units: downloads/others/eko (2)Eko specialized Builds (For Broadcom device only) If you spot something wrong or needed to be added, pm me.